Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Why Marietta Homeowners Choose Trane Air Duct Cleaning
We provide independent Marietta Trane service for air duct cleaning, and the work centers on one reality: Trane systems move air differently than other brands, so the cleaning has to follow that airflow, not fight it. Most standard whole-home duct cleanings in Marietta run $450 to $850 depending on system size and how much debris has settled inside. Omar Haddad and our crew know Trane’s variable-speed blowers, ComfortLink controls, and Hyperion air handlers well enough to clean the ductwork without throwing the system’s calibration off. We are not a Trane authorized dealer or factory service provider. We’re an independent shop with hands-on hours on Trane equipment, right down to the way red clay dust settles in the supply plenum. Call (762) 216-4075 for a written quote before any work starts.
Why Trust Cardinal Air Duct Marietta for Your Trane Air Duct Cleaning?
Trane builds its high-efficiency systems around tight airflow tolerances. That’s a good thing for heating and cooling, but it also means a dusty blower wheel or a partially separated flex duct shows up as a real performance drop, not just dirty air. Our technicians know which Trane components are sensitive to debris and which cleaning methods match them. When we clean a Trane XV20i variable-speed system, we account for the fact that the blower runs at low speeds for long stretches, pulling fine dust across the wheel and motor housing in a way single-speed units never do. A one-size-fits-all duct cleaning misses that. Our approach doesn’t.
Omar Haddad trained in heating and ventilation systems at Los Angeles Trade-Technical College and spent years learning the difference between a duct that needs brushing and one that needs replacing, without guessing. He runs every job with Rotobrush rotary brush systems and Nikro HEPA-rated vacuum extraction because, as he puts it, the tool should do the heavy lifting so the technician can focus on doing it right. For several years, Omar and his crew have served Marietta homeowners, including jobs near the Historic Marietta Square where older craftsman homes hide decades of debris inside their ductwork. Every Cardinal Air Duct Marietta booking includes a written price before work begins, background-checked and uniformed technicians, and the 365-Day Done Right Promise: if the work isn’t right within 365 days, we return and correct it at no charge.
Styles & brands we work with
Common Trane Air Duct Cleaning Problems We Fix in Marietta
These are the issues we see most often on Trane systems in Marietta homes. If any of them sound familiar, we can inspect and fix them properly.
- Mold and debris buildup in supply ducts of high-efficiency Trane heat pumps. Trane heat pumps like the XV20i run their variable-speed blowers at low continuous airflow to hold temperature steadily. That’s efficient, but it means air moves slowly enough that moisture and fine particles settle inside supply ducts rather than blowing through. In Marietta’s humid summers, that trapped material can turn into mold inside the duct lining. We see this most in homes where the AC runs almost nonstop from May through September.
- Blower motor dust accumulation in Trane variable-speed air handlers. The Hyperion air handler’s blower wheel collects a fine layer of dust from continuous low-speed operation. Over time, that layer thickens, throws the wheel out of balance, and forces the motor to work harder. The result is reduced airflow and sometimes a faint wobble you can hear through the vents. Cleaning the blower wheel properly requires pulling it from the housing, not just vacuuming around it.
- Flex duct separation at Trane plenum connections. Marietta attics get brutally hot in summer. The sheet metal plenum on a Trane air handler expands and contracts with that heat, and after enough cycles the flex duct connections can pull loose. When that happens, conditioned air spills into the attic instead of the living room. We routinely find two or three separated connections on systems that have never been inspected. Sealing them with proper mastic and fasteners, not duct tape, makes an immediate difference.
- Condenser coil fouling from pine pollen and cottonwood near Kennesaw Mountain. The outdoor condenser coil on any Trane system fights Marietta’s spring pollen season every year. Homes near Kennesaw Mountain get heavy pine pollen and cottonwood fibers that pack into the coil fins and cut heat transfer. A fouled coil makes the compressor work harder and shortens its life. Coil cleaning belongs in any Trane service visit, not just when the system breaks.
- Red clay dust caked inside original metal ductwork. Marietta’s red clay isn’t just a lawn problem. Decades of tracked-in clay, construction dust, and pet hair settle inside original metal ducts in 1960s to 1980s ranch and split-level homes. That layer can sit three inches thick in the return drops. Standard cleaning with a shop vac won’t touch it. You need a rotary brush system and negative-pressure extraction, meaning the loosened debris goes straight into the vacuum, not back into your living room.
Trane Parts & Our Repair-vs-Replace Approach
For critical Trane components like blower motors, control boards, and ComfortLink thermostats, we use genuine OEM parts when available. Those components are calibrated to Trane’s specifications, and substituting a generic part can change how the whole system behaves. For duct fittings, sealing materials, and flex runs, we select high-quality aftermarket options that match or exceed OEM specs. A piece of flex duct or a supply register doesn’t need a Trane logo to do its job well, and spending extra on OEM there doesn’t buy you anything.
Our repair vs. replace line is honest. If a blower wheel is caked with debris that won’t come off, we clean it. If the wheel is cracked or the motor bearings are shot, we tell you it needs replacement and quote the job straight. Severely degraded ductwork or evaporator coils beyond economical restoration get the same treatment: we recommend replacement, not endless patching. You’ll get a written price for any repair before we touch it. Call (762) 216-4075 to talk through what your Trane system needs.
Our Trane Service Process – Step by Step
Here’s how a typical Trane air duct cleaning goes at a Marietta home, start to finish.
- 1
System walkthrough and static pressure check. We inspect the air handler, return drops, supply plenum, and visible duct runs. On Trane systems with ComfortLink, we note the current airflow settings so the cleaning doesn’t change the system’s baseline.
- 2
Duct cleaning with HEPA extraction. We cut a small access port in the supply and return plenums, run a Rotobrush rotary brush through the ductwork, and keep the system under negative pressure with a Nikro HEPA vacuum. The loosened debris goes into the vacuum, not back into your home.
- 3
Evaporator coil and blower wheel service. For Trane air handlers, we pull the blower wheel, clean it thoroughly, and inspect the motor. We clean the evaporator coil with a non-corrosive coil cleaner approved for aluminum fins. This is where a lot of duct-only cleaners stop, but on a Trane system, skipping the coil and blower means the ducts get dirty again fast.
- 4
Flex duct inspection and sealing. Every Trane plenum connection gets checked for separation. We reseal loose connections with mastic and proper fasteners, because duct tape dries out and fails in Marietta attic heat.
- 5
System test and photo documentation. We run the system, confirm airflow and noise levels are back to where they should be, and give you before-and-after photos of the actual work. You get a digital invoice you can pay from your phone.
See the difference
Before
After
Before
After
Before
AfterTrane Products We Service & Install in Marietta
We work on all the common Trane residential product lines in the Marietta area. That includes the XV20i variable-speed heat pump, the XR14 and XB13 single-stage systems, and Trane Hyperion air handlers paired with both heat pump and gas furnace setups. The variables that matter for duct cleaning are the same across those lines: how the blower runs, how the coil collects debris, and how the ducts connect at the plenum. We don’t need to be a factory dealer to know each system’s failure points. We stock common flex duct sizes, mastic, registers, and air filters locally, so most jobs don’t require a second visit for parts.
We Also Service These Brands
While this page covers Trane specifically, we also handle Trane repair in Acworth and our Marietta crews work on all major brands. We service Lennox and Carrier systems regularly, along with other manufacturers. If you’re not sure what you have, call (762) 216-4075 and we’ll help you identify the system before scheduling anything.
FAQs – Trane Air Duct Cleaning Service in Marietta
Marietta’s red clay finds its way indoors on shoes, tools, and air currents, and it settles inside return ducts faster than most people expect. In older ranch and split-level homes with original metal ducts, red clay dust mixes with pet hair and construction debris into a packed layer that restricts airflow through your Trane system. The clay also holds moisture, which contributes to musty odors when the AC cycles. A standard duct cleaning with rotary brushing and HEPA extraction removes it. For a quote on your home, call (762) 216-4075.
Yes, and we do it as part of a full Trane duct cleaning job. The ComfortLink thermostat and its communicating sensors can accumulate a thin film of dust, especially if return registers haven’t been changed regularly. A gentle cleaning of the sensor housing with low-pressure air keeps the temperature readings accurate. We never use liquid cleaners on the thermostat board. If your ComfortLink is reading wrong or the system is cycling oddly, mention it when you call (762) 216-4075 and we’ll address it during the visit.
Blower motor noise right after a duct cleaning usually means the blower wheel is dirty or unbalanced, and the cleaning exposed it rather than caused it. When we clean Trane variable-speed air handlers, we pull the blower wheel when needed, clean it fully, and inspect the motor bearings. If the wheel was caked with debris, removing it changes the airflow pattern and can reveal a pre-existing balance issue. Our 365-Day Done Right Promise covers this: if the work isn’t right within 365 days, we return and correct it at no charge. Call (762) 216-4075 if your blower sounds off.
Yes, and the reason is the way Trane’s variable-speed blowers run. A high-efficiency Trane XV20i or Hyperion system moves air at low speeds for long cycles, which gives airborne dust and humidity more time to settle on the evaporator coil. That builds a film on the coil fins that reduces heat transfer and can freeze the coil in severe cases. We recommend coil inspection and cleaning more often on high-efficiency Trane systems than on basic single-stage units. How often depends on your home’s dust load and how much the system runs. Call (762) 216-4075 and we’ll help you set a sensible schedule.
A video inspection shows you the interior of your ductwork, which a visual check from the register can’t reach. In Marietta homes, we routinely find separated flex duct at the plenum, dead rodents inside return drops, and packed red clay dust layers in main trunk lines, none of which are visible from the vent opening. We use a small camera to document what’s inside your ducts before and after cleaning, and you get the photos. That’s part of The Relay Standard booking experience: live trackable arrival, before-and-after photo proof, and a written price before work starts. Schedule an inspection at (762) 216-4075.
No, and we don’t claim to be. We are an independent Trane air duct cleaning and service provider in Marietta. That means we’re not bound by factory dealership rules, but it also means we choose our parts and methods based on what’s right for the system and the homeowner, not what a manufacturer program requires. Our Trane knowledge comes from hands-on service work on real Marietta systems, not a dealership certificate. If warranty work is needed, you’ll still need a Trane authorized dealer for that portion, and we’ll tell you honestly if that’s the case.
Most Trane air duct cleanings for a typical Marietta home run $450 to $850 for the full system. That includes the supply and return ducts, blower wheel inspection and cleaning, and coil service where accessible. Larger homes with multiple air handlers or heavily contaminated ducts run higher, and we give you a written price before any work begins, so the number you approve is the number you pay. No per-vent pricing, no add-on surprises at the door. For an exact quote on your Trane system, call (762) 216-4075.
Book Your Trane Service in Marietta, GA
If your Trane system’s airflow is weak, your vents are dusty, or your ducts haven’t been cleaned since before the pandemic, let’s get it handled. Call (762) 216-4075 for a free estimate and a written price before any work starts. Dirty ducts don’t fix themselves, let’s just get it done right.
Written by Omar Haddad, Owner at Cardinal Air Duct Marietta, serving Marietta since he brought his Los Angeles HVAC training and hands-on Trane expertise to Cobb County.